JKBMS PRODUCT

JKBMS JK-PB Series

JK BMS V24 PB1A16S10P

100A-class V24 inverter BMS with 1A active balancing, CAN and dual RS485

A JK-PB smart BMS for lithium packs up to 16S, rated at 100 A continuous discharge and 1 A active balancing. Bluetooth, CAN, dual RS485 and display are listed. Use a compatible harness for the installation.

1 / 3
Разом$130.25

Деталі продукту

Комплект постачання та характеристики

Ключові особливості

  • V24.0.1 revision: 80V supply ceiling and -40 to 75 C operating range
  • Two-stage overcurrent protection: 200A for 9s, 300A for 2s
  • Chemistry-specific support: 7-16S Li-ion, 8-16S LiFePO4, 14-16S LTO
  • 100A maximum continuous charge and discharge
  • 1A active cell balancing
  • V24 standard interfaces: Bluetooth, CAN, dual RS485 and display
  • V24 standard functions: heating, two dry contacts, parallel current limiting and discharge precharge
  • Unchanged from V19: 300 x 100 x 24 mm, 14 accessories, RS485-2 cascade up to 16 units

Включено

  • Selected JKBMS smart BMS model or display bundle
  • Model-specific wiring harness and standard accessories supplied with the product
  • Documentation or setup references supplied with the selected package

Не включено

  • Battery cells, battery enclosure, inverter, charger, and external power cabling
  • External contactors, breakers, fuses, and installation hardware unless specified
  • Onsite installation, commissioning, firmware setup, or inverter configuration service
ModelJK-PB1A16S10P
SeriesJKBMS JK-PB Series
Overcurrent Protection200A for 9s (2x rated) / 300A for 2s (3x rated)
Battery ChemistryLi-ion (ternary/NMC) 7–16S; LiFePO4 (LFP) 8–16S; Lithium titanate (LTO) 14–16S
Series RatingLi-ion 7–16S; LiFePO4 8–16S; Lithium titanate 14–16S
Balance Current1 A active
Continuous Discharge100 A
Supply Voltage20–80 V
Operating Temperature-40°C to 75°C
Standard CommunicationBluetooth, CAN, RS485-1, RS485-2, display interface
DimensionsV24.0.1: 300 × 100 × 24 mm
WeightV24.0.1: 988 g
Manual RevisionV24.0.1 / V19.0.3

Product resources

Specifications depend on hardware revision. Use a compatible harness and follow the applicable installation instructions.

HARDWARE SPECIFICATIONS

JK-PB1A16S-10P data by hardware revision

The V24.0.1 energy-storage specification lists JK-PB1A16S-10P in the 100 A tier with 1 A active balancing, chemistry-specific cell counts, Bluetooth, CAN, two RS485 channels and a display interface. Compared with V19.0.3 the supply ceiling rises to 80 V, the operating range widens to -40 to 75 C and two-stage overcurrent protection is added. Match the hardware revision before wiring.

Battery compatibility

Chemistry changes the series range

Li-ion (ternary/NMC)
7–16S
LiFePO4 (LFP)
8–16S
Lithium titanate (LTO)
14–16S

Electrical limits

Use the correct rating label

Active balance
1 A
Continuous discharge
100 A
Supply voltage
20–80 V

V24.0.1 section 4.1 lists 100 A as the maximum continuous charge and discharge current for this tier; the effective protection value follows the configured parameters.

Interfaces and functions

Standard is not the same as optional

Standard

Bluetooth · CAN · RS485-1 · RS485-2 · display interface

Additional standard functions

Heating control · Two dry-contact outputs · Parallel current limiting · Discharge precharge

  • CAN and RS485-1 are provided for inverter communication.
  • RS485-2 is used for parallel communication or PC software.
  • Protocol compatibility, cable pinout and inverter settings must be confirmed for the target system.

Mechanical and environment

Match dimensions to the label

V24.0.1
300 × 100 × 24 mm · 988 g
Operating temperature
-40°C to 75°C
Revision control matters.
  • V24.0.1 lists JK-PB1A16S10P at 100 A maximum continuous charge and discharge current.
  • V24.0.1 raises the supply-voltage ceiling from 70 V to 80 V and widens the operating range from -30 to 70 C to -40 to 75 C.
  • V24.0.1 adds two-stage overcurrent protection: 2x rated current for 9 s and 3x rated current for 2 s.
  • Enclosure dimensions (300 x 100 x 24 mm), the 14-accessory pack and the RS485-2 cascade limit of 16 units are unchanged from V19.0.3.
  • Default parameter tables are identical apart from item 26, where the discharge precharge time changes to 3 s.
  • V19 and V24 wiring, connectors and harnesses must not be mixed by assumption.

TECHNICAL DOCUMENTS

Product manuals

Documentation review recorded 2026-11-18. Technical facts apply only to the named document and hardware revisions; this is not a manufacturing date.

Browse the official technical library →

Before ordering

Four details that prevent the wrong configuration

  1. Photograph the product label or confirm the exact hardware/manual revision.
  2. Provide battery chemistry, series count and expected charge/discharge demand.
  3. Provide the inverter brand and model, required CAN or RS485 protocol, and parallel-pack plan.
  4. Confirm display, communication cable, heating, dry-contact and precharge requirements in the order.

MODEL-SPECIFIC APPLICATION NOTES

JK-PB1A16S-10P selection context

JK-PB1A16S-10P should be compared as a specific JK-PB series product, not only by a copied title or image. The selection should be based on the real battery system, installation space, communication needs, and official quotation or checkout configuration.
Why this model matters

V24.0.1 hardware differs from V19.0.3 in supply ceiling, temperature range and overcurrent behaviour. Confirm the label and do not assume V19 harnesses, protection settings or default parameters carry over.

Application context

JK BMS V24 PB1A16S10P belongs to the JK-PB series and is best reviewed for 48V-class storage batteries and inverter-connected LiFePO4 systems.

The listed battery string range is Li-ion (ternary/NMC) 7–16S; LiFePO4 (LFP) 8–16S; Lithium titanate (LTO) 14–16S. The current reference is 100 A. The active-balancing reference is 1 A active.

For communication planning, this page lists Standard: Bluetooth, CAN, RS485-1, RS485-2, display interface; protocol, pinout, cable, firmware, and inverter or service-tool settings still need confirmation.

Decision checks

  • Battery chemistry or cell fit: Li-ion (ternary/NMC) 7–16S; LiFePO4 (LFP) 8–16S; Lithium titanate (LTO) 14–16S.
  • Mechanical planning: reserve space around V24.0.1: 300 × 100 × 24 mm, cable exits, airflow, and service access.
  • The product page lists the available configurations and accessories for direct checkout.
  • Use www.jkbms.net and zhou@jkbms.net to verify official source, quotation, and bulk purchasing details.

Model planning

Model fit and purchase planning

Use this summary to confirm whether JK BMS V24 PB1A16S10P fits the battery system before checkout, quotation, or installation.

Model
JK-PB1A16S-10P
Primary use
Inverter-connected LiFePO4 storage batteries
Battery strings
Li-ion (ternary/NMC) 7–16S; LiFePO4 (LFP) 8–16S; Lithium titanate (LTO) 14–16S
Current reference
100 A
Active balancing
1 A active
Communication
Standard: Bluetooth, CAN, RS485-1, RS485-2, display interface
Installation size
V24.0.1: 300 × 100 × 24 mm

Selection details

  • JK BMS V24 PB1A16S10P should be checked against the real battery pack, load current, installation space, thermal conditions, and selected accessories before purchase.
  • The listed 100 A current reference must be matched with cable size, terminals, fuse or breaker, battery cells, thermal design, and expected inverter demand.
  • The listed communication options are Standard: Bluetooth, CAN, RS485-1, RS485-2, display interface; protocol, pinout, firmware, and inverter compatibility still need project-level confirmation.
  • The 1 A active balancing specification is one selection factor and does not replace matched cells, correct wiring, or suitable charging settings.

System fit checks

Compatibility, installation, and official purchase checks

Use these checks before selecting a configuration, requesting a quote, or installing the product in a battery system.

Compatibility

Match the product to the battery system

Confirm the battery pack is within Li-ion (ternary/NMC) 7–16S; LiFePO4 (LFP) 8–16S; Lithium titanate (LTO) 14–16S. Match the 100 A current reference to the inverter, load, wiring, protection, and thermal design. Use the 1 A active active-balancing class as one selection input, not as a substitute for good cell matching.

Communication

Confirm protocol and interface details

Communication status: Standard: Bluetooth, CAN, RS485-1, RS485-2, display interface. Confirm protocol, pinout, baud rate or CAN bitrate, firmware, and inverter compatibility before installation.

Installation

Plan wiring, mounting, and operating conditions

Reserve space for the listed dimensions: V24.0.1: 300 × 100 × 24 mm. Plan the installation around -40°C to 75°C operating conditions. Use suitable fusing, cable size, torque, ventilation, insulation, and commissioning checks for the final battery system.

Official source

Verify the product and quote channel

Verify this product on https://www.jkbms.net/products/jkbms-v24-jk-pb1a16s10p-inverter-bms-16s-100a-1a-active-balance, confirm the official domain is www.jkbms.net, and use zhou@jkbms.net for quotation checks before bulk payment or project procurement.

Product FAQ

JK-PB1A16S-10P compatibility, configuration and purchase FAQПитання та відповіді

How do I choose the correct BMS for my battery?

Provide the chemistry, exact series count, continuous charge and discharge current, and peak current with its duration. Then check balancing current, installation space, cooling, inverter, hardware revision and matched wiring. Nominal voltage, a series name or a similar connector alone does not establish compatibility.

Can I add a 4.3-inch display and WiFi module to this BMS?

Yes. The current catalogue offers these options for this BMS, independently or together. Each selected accessory is supplied once per BMS; a display already included in the selected package is not charged twice. The adapter and harness must be compatible with the BMS and display.

Do two selected accessories give a 10% discount?

No. Selecting a display or WiFi applies the 5% discount once to the BMS and those accessories. Two accessories do not double the discount. H/C/R/P feature fees do not trigger or receive the discount and are added in full afterwards.

Can this BMS be ordered with a 7-inch display?

Yes. This page belongs to the PB series, which offers the 7-inch display option. The display adapter and harness must be compatible with the BMS.

Can I add heating, CAN and RS485, and what do they cost?

H means heating interface, C means CAN and R means RS485. All PB-series models include H, CAN and RS485 as standard. B2A32S-RP includes CAN and RS485 as standard, with H available as an option. Included features require no selection or extra charge. Each feature not already included costs USD 1 per BMS. Features included in the model are not offered or charged again. The final model retains existing feature letters and adds only newly selected options in H, C, R order, preserving any existing PB suffix. Option fees are added after any 5% bundle discount and do not trigger it. The model, hardware revision, application protocol and harness must suit your inverter.

Does CAN or RS485 guarantee compatibility with my inverter?

No. Compatibility depends on the inverter and BMS, hardware revision, application protocol, firmware, pinout, cable and settings. A website selection or a matching connector does not prove that the two devices can communicate.

Which battery cell counts does JK-PB1A16S10P support?

The V24.0.1 manual lists 7-16S for ternary/NMC lithium, 8-16S for LiFePO4 and 14-16S for LTO. Select by chemistry as well as series count.

What changed between V19 and V24 on JK-PB1A16S10P?

V24.0.1 raises the supply-voltage ceiling from 70 V to 80 V, widens the operating range to -40 to 75 C, adds two-stage overcurrent protection at 2x and 3x rated current, and moves the discharge precharge time to 3 s. Enclosure dimensions, the accessory pack and parallel behaviour are unchanged.

Is 100 A a continuous rating on JK-PB1A16S10P?

Yes. V24.0.1 section 4.1 lists 100 A as the maximum continuous charge and discharge current for this tier. The effective protection value follows the parameters configured on the unit.

Are CAN and RS485 standard on JK-PB1A16S10P V24?

For the V24.0.1 configuration, Bluetooth, CAN, two RS485 channels and a display interface are listed as standard. CAN and RS485-1 serve inverter communication; RS485-2 serves parallel communication or PC software. Protocol and cable compatibility still require confirmation.

Can a V19 harness be reused on a V24 JK-PB1A16S10P?

Do not assume so. V19 and V24 connectors, wiring and harness definitions must be matched to the actual hardware revision before connection.

RELATED PRODUCTS

Review nearby models in the same product family before confirming strings, current rating, balancing, display, or communication requirements.

Get in Touch

Ready to power your future? Contact us for a custom quote or partnership inquiry.

LocationRoom 1008, Building B4, Yunzhi Science & Technology Park, Guangming District, Shenzhen, China

За згодою JKBMS зберігає категорії джерел і етапи покупки до 90 днів. Підсумок джерела може зберігатися із замовленням. Необов’язкова статистика відвідувань і покупок.

Дозвольте рекламні cookie Google та ідентифікатори кліків для зв’язування покупок із рекламою. Потрібна згода на статистику. Імена, контакти та адреси не передаються. Персоналізація реклами залишається вимкненою.

Політика конфіденційності